Bridge Pin
Bridge Pin
Coraopolis Bridge
The Sixth Street bridges
Note: Material from this section is adopted from the HAER report on this bridge.
The through truss spans incorporated in the present Coraopolis Bridge were originally erected across the Allegheny River at Sixth Street in Pittsburgh, linking Pittsburgh with the main business thoroughfare of neighboring Allegheny City. This was the third of four bridges to serve that location, which is considered among Pittsburgh's most important river crossings. The growth of Pittsburgh was strongly influenced by its numerous waterways, and the successful linking of the city with its neighboring communities by means of bridges was a significant factor in the development of its metropolitan identity. Allegheny City was annexed by Pittsburgh in 1907, becoming the city's "North Side".
First Sixth Street Bridge
The first bridge to cross the Allegheny at Sixth Street was a six-span, flat-roofed, covered wooden bridge constructed in 1819. This bridge had a total length of 1,037 feet, consisting of four 185 foot spans, a 170 foot span, and a 137 foot span. The design and construction of this bridge have traditionally been attributed to a Mr. Lothrop; it was presumably a Burr arch truss, like the Ninth (Hand) Street Bridge, another of Lothrop's products. Physical evidence for this assumption survived until the 1890s, when an observer reported that the skewbacks from the wooden arches remained visible in the north abutment.
Second Sixth Street Bridge
In 1860 a wire-suspension bridge, designed by John A. Roebling, replaced the decaying timber structure. This bridge was four spans long, with two 344-foot main spans, and approach spans measuring 177 and 171 feet each. The bridge was dominated by cast iron towers, each formed by four cast iron columns.
Although the Roebling bridge, with its iron superstructure, was generally believed non-flammable, it fell victim to fire on June 19, 1881. The bridge was not destroyed, but its floor system of white pine and white oak was severely damaged. John Harper, president of the Allegheny Bridge Company, which owned and operated the structure, stated that he believed the fire was the result of "sparks and perhaps flame from the stacks" of passing steamboats igniting bird nests located under the superstructure of the bridge. After heavy electric streetcars were introduced to the bridge in 1890, concern over its functional capacity grew, and in 1891 plans were begun to replace the suspension bridge with one that could better handle the steadily increasing traffic, as well as permit trolleys to cross without reducing their speed.
Third Sixth Street Bridge
Coraopolis Bridge, from below deck, showing deck girders, eyebar tension members, lattice girders of truss superstructure
The third Sixth Street Bridge was designed by the nationally-significant engineer Theodore Cooper (1839-1919). This bridge has been identified as the last surviving structure entirely designed by Cooper, whose involvement extended even to such details as the bridge's handrail, lamps, and fascia.
The third Sixth Street Bridge, like most roadway river bridges in the 19th century, was privately built and operated as a toll crossing. The total cost of construction was $560,000. This cost was underwritten by the Sixth Street Bridge Company and Fidelity Title and Trust Company, successors to the Allegheny Bridge Company, which had received its charter in 1810. When the bridge was opened in 1893, the toll was set at two cents for each man, while women crossed at no charge. Beginning in the late 1890s, Allegheny County and the City of Pittsburgh undertook a systematic program of acquiring the privately owned bridges within their jurisdiction and eliminating their tolls. The Sixth Street Bridge was purchased by Allegheny County in 1911 along with nine other bridges at the combined price of $2,851,000; all ten of these bridges were subsequently declared free.
The trusses for the third Sixth Street Bridge were fabricated by the Union Bridge Company. This company had been formed in 1884 by the merging of the Central Bridge Company of Buffalo, New York, and Kellogg and Maurice of Athens, Pennsylvania. The Buffalo plant was closed around 1890, so presumably the trusses were produced in the shops which remained at Athens.
Coraopolis Bridge with newer pony truss at left, from SE (Coraopolis side)
The superstructure was erected by the Baird Brothers, John and William, who first advertised in the Pittsburgh and Allegheny City Directory in 1886 as contractors located at Home and Valley Streets. In the 1891 and 1892 editions of the Directory they were listed as bridge builders; their listings no longer appeared by 1900, and by 1911 William Baird had left the construction business and had begun managing a hotel.
The Baird Brothers had been involved with numerous bridge projects and companies in the late nineteenth century. William Baird had worked on seven bridges crossing the Missouri River, the Merchants Bridge across the Mississippi River at St. Louis, two bridges crossing the Ohio River at Wheeling, West Virginia, the bridge carrying the Baltimore & Ohio Railroad across the Susquehanna River, and bridges at Steubenville, Ohio, and Poughkeepsie, New York. John Baird had also been involved in the construction of the Eads Bridge in St. Louis and the Cairo bridge in Memphis, and had been employed by the McCann Construction Company, the Keystone Bridge Company and American Bridge Company.
This bridge was also outgrown.
While the Pittsburgh City Council and the Municipal Affairs Committee of the Chamber of Commerce argued for the retention and upgrading of the existing bridges, the issue was ultimately decided by the Department of War, acting under the authority of Section 18 of the Rivers and Harbors Act of March 3, 1890 (30 Stat., 1121-1153). This act empowered the Secretary of War to require the removal or alteration of any bridge which " ... is an unreasonable obstruction to the free navigation . . . on account of insufficient height, width of span, or otherwise". So, unfortunately, the War Department decreed that the numerous bridges over the Allegheny with their differing spacing of piers, main spans, and generally low clearances, were an impediment to navigation, and decreed that all bridges would have to be replaced. Although the decree was discussed in the early 1900s, and first issued in 1917, serious work did not begin till 1924. As part of the Three Sisters (Pittsburgh) project, the bridges at Sixth, Seventh, and Ninth Streets were to be demolished and replaced. The other two bridges were destroyed and scrapped, but the Cooper Bowstring trusses were moved to Coraopolis and reused.
Moving the Sixth Street Bridge to Coraopolis
Note: The material in this section is taken from a different HAER report.
The 1892 Sixth Street Bridge (as described above, a pair of camelback Pratt trusses and the third bridge built in this location) had a second chance. In 1927, it was lowered from its piers, the top chords partially disassembled. The structure was floated downriver to a new location over the Ohio River back channel between Coraopolis and Neville Island to make way for the current Sixth Street Bridge structure.
A forced opportunity
The Cooper spans remained in good shape, and concerns for economizing in public works projects led to recycling of the 1892 bridge. Commissioner Armstrong took credit for proposing to reuse the Cooper bridge instead of building an entirely new structure in nearby Coraopolis, saving Allegheny County $350,000. The Foundation Company bid on a contract to move the Sixth Street Bridge from its site in downtown Pittsburgh to Coraopolis, twelve miles away. Winning the contract at a bid of $316,200, the company also assumed any risk that the spans would sink or be damaged during the project. The company allowed pedestrians to cross the structure while roadway removal proceeded in the fall of 1926 in order to reduce the inconvenience for residents. Workers took off half of the roadway at a time, leaving pedestrian areas accessible until final segments were taken away
Coraopolis Bridge with newer pony trusses in background, filigree work and decorative mesh of arched openings in foreground. Built up compression girder members at side, and tierod bracing also visible at top of arch
Removal process
The bowstring trusses, in addition to weighing 1,600 tons each, presented the difficult problem of being slightly too tall to fit under two bridges along the journey. Because of the stresses inherent in a bowstring truss, the Foundation Company could not merely disassemble them; instead, the firm had to transport the entire 450'-0" spans, which were 44'-0" wide and 80'-0" high.
Each truss consisted of sixteen eye-bar panels pinned together. Removing one part would break the structure's rigidity and make moving it very difficult. Instead of shifting the spans off piers for lowering or pivoting them from their present support, the Foundation Company lowered the structure in position, taking off the masonry and using substitute supports for resting the structure without getting in the way of the process. The contractor attached a frame to each of the piers and abutments, used straps to bind the trusses to each frame, and lowered them using the straps.
With twenty-six 7" holes punched in the strap, the company used a matching chain to counter the eight straps. Using pins to move the strap by hole sets, the company brought the spans downward 15" at a time with jacks. The pins attached to the plungers of eight 500-ton jacks. The jacks remained in place while the pins moved 15". The water-cylinder jacks were also 15" high, capable of exerting 3200 psi after pumping. By bleeding water out of the cylinders of the jacks all at once, workers used the four jacks on each side of the bridge to lower the spans on alternate sides to the full depth of 16-0.
Transport
Workers made a pontoon out of two pairs of barges, spaced to create a platform 400'-0" long and 52'-0" wide, which carried the bridge with 20'-0" of overhang. Stringers supported the bridge in forty-two places, with a 40-ton screw jack at each stringer for easier loading and unloading. When workers reached the Manchester Bridge, they had to adjust the bridge to fit the clearance, which was 14'-0" and 12'-0" less than the bridge height. After supporting the bridge under the floor beams, they disassembled the top chord and stabilized each panel point on the trusses. Steering the bridge under the Manchester Bridge and the railroad bridge at Brunot's Island, the tugboat captains went through the Ohio River lock and up the back channel toward Coraopolis, where piers and abutments had been constructed.
Reassembly
Reversing the process and using the same jacks and steel frames to raise the structure 32'-O", the company erected the Cooper bridge 30 days after the project began.
The Farris Engineering Company, a Pittsburgh company located in the Empire Building, performed a great deal of work on the bridge at its new location. The original approved contract for their work had a price total of $271,811.50. They built portions of the substructure that the Foundation Company had not done. Farris also erected the two pony truss approach spans, repaired and painted the main superstructure, and paved the bridge deck and the two approaches.
The approach spans, and the end bearings for the main spans, were fabricated by the American Bridge Company at its shops located in Ambridge, Pennsylvania.
End of life
Allegheny County ended up replacing the Coraopolis Bridge with a new bridge at this location. By the 1980s, due to its deteriorated condition and inadequate load carrying capacity, the four span truss bridge did not meet the transportation needs of its location.
After nearly 50 years of additional service, which included weight restrictions and closings during cold weather (for a time it was restricted to carrying vehicles with a maximum weight of three tons, and it was only open to vehicular traffic during periods when the temperature is above 30 degrees Fahrenheit), the old bridge was replaced by a unremarkable deck girder bridge which was completed in 1995.
Thus, eventually it was closed, replaced, and demolished, ending a unique chapter in American bridge history.
Notes
^ The town Coraopolis (and therefore the bridge) are sometimes referred to as Corapolis, that is, missing the 'O' between the 'A' and 'P', which can make searches somewhat difficult. For example the HAER material is indexed this way although the HAER article text uses the spelling with the 'O'.
^ The trusses are conflictingly referred to in different sources as "Bowstring", "Pennsylvania" or "Pratt". Pratt is the most common name. Bowstring may refer to the shape of the bridge, it has some resemblance to a bow, with the roadway as the string (in this particular truss design instance, the members at the road level are eyebar, as can be seen in the belowdeck illustration, above, and thus are in tension only, which also may be why it's named that way) This tension only, pin joint construction is the major factor making the move difficult.
^ The HAER (Historic American Engineering Record) report gives an extensive history of the various bridges at the 6th street site, and of this bridge once moved. It is available in .tif form at external link #4, but Bruce S. Cridlebaugh of pghbridges.com has already scanned the text in. This text is available at external link #5.
^ The HAER (Historic American Engineering Record) report gives an extensive history of the various bridges at the 6th, 7th and 9th street sites, and some info on this bridge once moved. It is available in .tif form at external link #6, but Bruce S. Cridlebaugh of pghbridges.com has already scanned the text in. This text is available at external link #7.
^ This image shows the removal and barge loading process. This image (both from the pghbridges.com site) shows a truss loaded on the barge and being moved. The top chord has been disassembled to allow clearance of some bridges it must pass under.
External links
Coraopolis Bridge at Structurae
Historic American Engineering Record (HAER) No. PA-217, "Coraopolis Bridge"
Image at HAER.
report HAER "Corapolis Bridge, Spanning Ohio River back channel at Ferree Street & Grand Avenue, Corapolis, Allegheny County, PA" 21 pages
Text of 21 page HAER writeup at pghbridges.com (this text is in the public domain since it is taken from the Library of Congress HAER report).
report HAER "Three Sisters Bridges, Spanning Allegheny River at Sixth, Seventh & Ninth Streets, Pittsburgh, Allegheny County, PA" 43 pages.
Textof 43 page HAER writeup at pghbridges.com (this text is in the public domain since it is taken from the Library of Congress HAER report).
article at pghbridges.com
Google Maps Composite image zoomed in, showing replacement bridge.
Categories: Bridges completed in 1892 | Bridges completed in 1927 | Bridges in Pennsylvania | Truss bridges | Bridges on the National Register of Historic Places | National Register of Historic Places in Pennsylvania | Tied arch bridges | Bridges over the Ohio River
About the Author
I am China Manufacturers writer, reports some information about brass paper towel holder , bath towel cabinet.
What kind of bridge pin do i need for my acoustic guitar?
i have a guitar and i was removing the bridge pin, but it went flying when i took it out with string, can i buy a set of bridge pins? if so does it have to be a specific kind?
no, just a standard acoustic bridge pin set should do her, order one or pick one up from your local guitar center( or other guitar supplier)
Bridge Pin
Graph Tech's TUSQ Nuts, Saddles and Bridge Pins (HD)
|
|
Brooklyn Dodgers Brooklyn Bridge Bat Pin $14.62 Brooklyn Dodgers Brooklyn Bridge Bat Pin Brooklyn Dodgers Brooklyn Bridge Bat Pin |
|
|
2010 Winter Olympics Torino Bridge to Vancouver Collectible Pin $3.99 Give a nod to the last Winter Olympics with the Torino to Vancouver Bridge collectible pin featuring the official logos of the 2006 and 2010 Games! |
|
|
2012 Team USA London Bridge & Yeoman Pin $6.95 After four long years of waiting, the 2012 London Olympics are finally here. Commemorate the Summer Games and get ready to watch Team USA bring home the gold with this collectible Team USA London Bridge & Yeoman pin. You can accessorize your latest USA Olympic Team-spirited attire with this pin that features a vibrant, enamel Team USA Shield next to the London Bridge and a British Yeoman guard. Itâs perfect for showing off your USA Olympic pride anywhere you go for years and years to come! |
|
|
Fender Bridge Pin Set (6-Pack) - Cream $7.99 Replace your bridge pins with this 6-piece set designed to fit Fender acoustic guitars. |
|
|
Fender Bridge Pin Set (6-Pack) - Black $7.99 Replace your bridge pins with this 6-piece set designed to fit Fender acoustic guitars. |
Knowledge and collects of lapel pins
Custom lapel pins is that status, occupation, honors and other special sign. According to historical load, wear a custom lapel pins begins in China's Song dynasty. In order to prevent further posing messenger, the court will be provided to each send a special envoy marked silver, Korea to an audience wearing the body. Since then, the practice of wearing a custom lapel pins on from generation to generation has been in use.
Custom lapel pins, including custom lapel pins, collar, cap sign, shoulder patches, armbands, armbands, medals, decorations, medals, custom lapel pins and so on. Many different kinds of custom lapel pins, production materials, except metals, there are marble, enamel, plastic and glass, precious stones. Variety of shapes, round, square, rectangular, diamond, cross, polygon and so on.
Military medal of the class
Various times of war, peace and meritorious service during the medal, Medal of Honor, rank of the warlord era medals, ribbon custom lapel pins, etc., are examples of such. Foreign medals also include a variety of campaign medals.
In recent years, Russia has become a collection of medals as a way to invest in accumulating wealth, their prices an average growth rate of 5%. Medal would depend on supply and demand in some circumstances. For example, Revolution Medal in the late 80s the price of 250 U.S. dollars, 60 dollars in 1998 which can buy. Events for August 1991 granted a "defender of freedom in Russia" medal, first Scoop 60 U.S. dollars, was because too many owners, not 10 dollars can buy.
Travel medal
What most medals with local characteristics, great development potential, China's tourism chapter 80 gradually prospered. Custom lapel pins made from lead sheet material, aluminum alloy to produce increasingly sophisticated. Completion of a new attraction, tourism also will release chapter. Such as Shanghai Yangpu Bridge, Shanghai's new attractions, visitors, the can buy exquisite bridge to the small custom lapel pins.
Tour features the largest chapter reflect typical local attractions. Great Wall, such as the majestic, white stupa Wutai Mountain and so is not readily available elsewhere, which is quite attractive to tourists.
New China issued the first set of gold medals, in 1979 by the China Mint Company foundry; the PBC issued scenic Beijing gold medals, a total of four. The positive pattern for the Tiananmen Square Chinese table and "Beijing 1979" on the back design was the Great Wall, Beihai Sule Pagoda, Temple of Heaven Qi Niandian and the Summer Palace. Diameter 27 mm, each costing 0.5 ounces with gold, purity is 91.66%, for the precious metals collection.
Logo Custom lapel pins
Factories, companies, schools, enterprises, mass organizations and party logo custom lapel pins, including the authority of the flag custom lapel pins. Such as the China Central Television-owned TV production center, its emblem is a rectangular, rounded lines outside the middle marker for the center, the center under the name of the abbreviation "C17C", background color or white gold, a prominent theme, clear.
Some foreign brand identity custom lapel pins, small size, has a decorative and inexpensive. As people's preference for certain brand-name products, the demand for these custom lapel pins is growing rapidly. On the other hand, these custom lapel pins are presented to customers, are generally not mass production.
These are many custom lapel pins on the market currently, and many adulterants. We must know below categories for find the real thing.
Fabrications get really into fake products and imitations. The most serious is the second chapter that is really fake object, the majority of copper, fake employer who work rust, and some to reduce costs, the copper into aluminum and tin products chapter. Different from the weight, billet judge different aspects, Discrimination wealth of practical experience is the key to success.
About the Author
Custom lapel pins by HiLP lapel pin manufacturer since 1993.
HiLP one of professional lapel pin manufacturers in China, we've more than ten years' experience in custom made lapel pins, badges, coins and other metal promotional items.
Read more: http://www.articlesbase.com/business-ideas-articles/custom-pins-is-a-good-promotional-tools-for-your-business-2285076.html#ixzz0ovSMhXpW
Under Creative Commons License: Attribution
|
|
City Landmark 2.25 inch Large Badge Style Round Fridge Magnet Golden Gate Bridge San Francisco $1.50 UK Produced decorative item... |
|
|
Signalinc Repeater 3WIRE 220V Coupler & Signal Repeater $67.99 Improve reliability with your home automation system. SignaLinc Plug-in Coupler-Repeater is the world's first plug-in signal coupler-repeater designed to increase the reliability of your system by simply plugging into an existing dryer outlet! The SignaLinc Plug-in Coupler-Repeater simply plugs into an existing clothes dryer outlet. Unlike previous solutions, which typically involve hiring an el... |
|
|
City Landmark 2.25 inch Large Badge Style Round Fridge Magnet Tower Bridge $1.50 UK Produced decorative item... |
|
|
Building Big - Bridges [VHS] $8.86 Bridges, more than humanity's other nature-defying structures, demonstrate our need to connect, and that lends their builders a certain artistic, even romantic, credibility. So symbolic is the bridge-builder's occupation, we discover early on in this episode of the Building Big series, that worshipers whittled the early Italian term for the job into the current word Pope. They might have thought t... |
|
|
Leigh D4R-24 Dovetail Jig $549.99 With the ability to cut half-blind-, through-, and sliding dovetails right out of the box, the Leigh D4R Pro 24-Inch Dovetail Jig allows you to customize the spacing of your joints for a classic hand-cut look. You can work with boards up to 24 inches wide and 1-1/4 inches thick, and the Leigh D4R Pro comes with an easy-to-understand instructional manual and DVD. With the option for five additional... |
Bridge Pin